Installation Guide
Safety and Warnings
Installation must be undertaken by a licensed electrician only
Keep the charger away from explosive or flammable materials, chemicals, vapors and other hazardous objects.
Keep the charge’s socket clean and dry. If it gets dirty, please wipe it with a clean, dry cloth.
Do not touch the socket pin when the unit is powered on.
Do not use the charger if it is showing any visible product damage such as cracks, abrasions, bare leakage, and other visible defects. At first sight of such damages, immediately contact a qualified technician.
Do not attempt to dissemble, repair or refit the charger. If necessary, please contact the qualified technician. Improper operation will result in device damage, electric leakage and other hazards.
In case any abnormal condition happens, please turn off incoming power supplies immediately.
Please consider charger protection against lightning and heavy rain.
Keep children away from the charger.
During charging, do not drive the EV. Charge only when the EV is stationary. For hybrid cars, charge only when the engine is switched off.
Our packaging materials are environmentally friendly and can be recycled. Please put the packaging in applicable containers to recycle it. Do not dispose of this device with the household waste. It should be taken to a suitable facility for recycling of electrical and electronic devices. For more detailed information about recycling of this device, please contact your local city/town council office or your household waste disposal service.
Package Contents
Insulated Terminal (*3) for single-phase (*5) for three-phase
M4*32 Screw (*6)
6 Wall Plugs (*6)
RFID Activation Card (*2)
Dismounting Tool (*1)
Cable Holder (*1)
User Manual (*1)
M4 Hex Key (*1)
Mounting Position Template (*1)
Product Information
External Structure
Product Details
RFID card sensor area
LED indicator
Logo
Front panel
Cable holder
Charging connector
Housing
Charging cable
Mounting hole
Drain hole
Network cable inlet
Power cable inlet
Specification
Installation Details
Opening
Step 1
Remove the two screws at the bottom.
Step 2
Use the dismounting tool to pry the marked points (1~3) along the edge in order.
Step 3
Pry the marked points (1~3) along the edge on another side in order
Step 4
Finish opening the external cover
Mounting
1) Based on the installation position template, identify the installation position and mark the two holes for the wall screws, which will be inserted in the top rear of the charger.
2) Drill two holes with the 6mm diameter drill bit and insert the plugs horizontally into the holes, paying attention to the force and depth with which they are inserted (make sure the plug completely enters the hole).
3) Insert the two M4x32 screws into the wall plugs, allowing the heads of the screws to protrude by at least 5 mm.
4) Provisionally position the charger by inserting the head of the screws into the upper holes at the rear.
5) Open the front of the charger.
6) Mark the position of the third fastening screw. The hole is located at the bottom of the charger.
7) Remove the station and make the third hole, inserting the wall plug.
8) Reposition the station and secure the third screw at the bottom.
Operation anD Configuration
CHARGING OPERATION - PLUG & CHARGE
Standby
A green indicator flashing slowly for 1s at 3-sec intervals indicates the charger is ready to use.
Plug in
Plug the charging connector into your EV's charging socket.
A green indicator flashing for 200ms at 1-sec intervals indicates the charging connector is plugged in.
Charging
A green indicator breathing at 1-sec intervals indicates the charging is in progress.
Fully Charged
Solid green light indicates the EV is fully charged.
Unplug
Unplug the charging connector.
Return to standby mode after the charging has finished.
CHARGING OPERATION - USE RFID CARD
Standby
A green indicator flashing slowly for 1s at 3-sec intervals indicates the charger is ready to use.
USE RFID Card
Plug the charging connector into your EV's charging socket.
A green indicator flashing for 200ms at 1-sec intervals indicates the charging connector is plugged in.
Evchargo APP
Evchargo is your charger’s companion app. After connecting your
charger to Evchargo, and select the scenario for home, you can use
the app to intelligently control your charger and enjoy the charging
service.
Use your mobile device to scan the QR code (left) below to download
and install Evchargo app, and scan the QR code (right) below to view
the user manual of the Evchargo.
Evchargo Download
(IOS&Android)
Evchargo APP instruction
AP Mode
The Hotspot interface is intended for the local configuration of the charger. A
smartphone is needed to connect the charger hotspot.
You can initiate the Hotspot interface by following the instructions.
Preparation - Activate the Hot Spot
Activate the hotspot of the charger by
restarting the power.
The hotspot of the charger remains available
for 15mins since charger reboot.
Connect to Charger Hotspot
Turn on the smartphone Wi-Fi, and connect
the hotspot of the charger. If unable to connect,
try using Airplane mode.
The name of the hotspot Wi-Fi starts with the
charger SN number, i.e. ”SN…” .
The password is admin123.
Login
Open the browser on your smartphone and enter 192.168.4.1 in the address
bar.
Log in using the four-digit PIN code located on the last page of the manual.
After login, the function menu will be displayed.
Configuration
Notice: When the configuration is successfully done, you need to reconnect the smartphone
to the charger hotspot. Then go back to the web page. It will automatically jump to the login
page.
Login again to start charging setting.
Troubleshooting
Note:
If the problem occurs, please contact customer service:
support@evswitchstore.com.au
Maintenance
Warranty
Period: Unless otherwise stated by local laws, we will provide a limited
warranty of up to 1 year starting from the date of purchase.
Scope: The charger and charging cable.
The limited warranty does not cover the following :
1. Normal wear and tear.
2. Damage or failure caused by unauthorized upgrades conducted by a
customer.
3. Damage or failure caused by external factors such as fire, flood, abnormal
voltage, other natural disasters, and secondary disasters.
4. Damage or failure caused by improper handling of the charger,
such as impact from a fall and careless transportation after
purchase.
5. Damage or failure caused by a customer not following the user
manual.
6. Damage or failure caused by non-equipment factors like human error
by a non-authorized individual carrying out maintenance.
7. Unauthorized repairs will render the limited warranty void.
8. Damage or failure caused by external factors such as power grid
malfunctions.
Limitation of liability:
We has compiled this document to the best of its knowledge but cannot
guarantee that all information provided is error-free, nor will it accept
liability in this respect.
To the maximum extent permissible under local applicable law, we
hereby disclaims any and all indirect, incidental, special and consequential
damages arising out of or relating to the AC Charger, including, but
not limited to, loss of time, loss of income, loss of use, loss of personal or
commercial property, inconvenience or aggravation, emotional distress
or harm, commercial loss (including but not limited to lost profits or earnings),
incidental charges such as telephone calls, facsimile transmissions,
and mailing expenses. To the maximum extent permissible under
local applicable law, we will not be liable for any direct damages in an
amount that exceeds the market value of the AC Charger at the time of
the claim.
The above limitations and exclusion will apply whether or not the customer’s
claim is in contract, tort (including negligence and gross negligence),
breach of warranty or condition, misrepresentation (whether
negligent for otherwise) or otherwise at law or in equity, even if we has
been advised of the possibility of such damages or such damages are
reasonably foreseeable.
Nothing in this manual shall exclude, or in any way limit, our liability for
death or personal injury solely and directly caused by their negligence, or
that of its employees, agents, or sub-contractors (as applicable), fraud,
or fraudulent misrepresentation, or any other liability to the extent the
same is proven in a court of competent jurisdiction in a final non-appealable
judgment and may not be excluded or limited as a matter of local
law.